1/2 THE COST OF REAL STONE - WEED FREE - PATTERN ADJUSTABLE - EASY CARE
ASHLAR SLATE COBBLE STONE BARN FLOOR A GREAT INTERIOR "GARAGE OR BASEMENT" ROMAN ROUND BASKET WEAVE BRICK SLATE COBBLE SLATE BRICK
Color Hardener
Stampcrete Color Hardener is specially formulated to be easily incorporated into the durable, abrasion-resistant surfaces, which offer streak-free vibrant colors, providing an attractive and long-lasting finish for any type of traffic. Stampcrete hardeners are longer wearing, easier to maintain, and more resistant to the effects of freeze/thaw cycles and salts. Textured surfaces may be implemented with this system to give authentic appearance variations where applicable.
SERPENTINE COBBLE
STANDARD COLORS
ACH-21 ANTIQUE RED
ACH-83 GRANITE SUN GRAY
ACH-22 BRICK RED
ACH-42 BUFF SUN BUFF
ACH-85 DARK GREY
ACH-23 TILE RED
ACH-81 SILVER GRAY SABAL
ACH-52 CORAL
ACH-53 TAUPE
ACH-40 BEIGE
ACH-45 RUSSET
ACH-50 SAND ADOBE BUFF
ACH-44 SANDSTONE
ACH-10 WHITE
ACH-46 BROWN
ACH-47 CORDOVAN
ACH-27 TERRA COTTA
ACH-88 CHARCOAL
ACH-48 CHOCOLATE
ACH-30 ANTIQUE WHITE
ACH-04 BURNT SIENNA
ACH-31 SAFETY YELLOW
ACH-29 BURNT ORANGE
ACH-01 CREAM
ACH-25 PEWTER
ACH-26 CARMEL
ACH-03 CURRANT
ACH-02 PALMETTO
Release Agents
Stampcrete Powdered Release Agents are a dry blend of chemical powders and color pigments, used to achieve accent colors and various color variation to textured surfaces in decorative stamped concrete. Stampcrete Release Agent allows the clean release of decorative stamps from the concrete surface by acting as a barrier between the concrete and the texturing tools.
STANDARD COLORS
SR-19 DARK GRAY
SR-17 LIGHT GRAY
SR-16 TERRA COTTA
SR-21 CHARCOAL
SR-14 BRICK RED
SR-12 DARK BROWN
SR-20 SLATE GREEN
SR-13 LIGHT BROWN
SR-18 MEDIUM GRAY
SR-15 SAND
SR-23 PENN BLUE
SR-24 WHITE
SR-04 MEDIUM BROWN
Technical Data / Installation Specifications updated 7-20-09
GENERAL Stampcrete System is cast-in-place concrete, integrally colored and stamped with U.S. patented platform/texturing tools to produce a surface similar to natural stone, brick, slate and other natural paving materials. Base color is achieved through integral color pigments in the concrete mix or surface treated with color hardeners. A powdered color release agent is used in the stamping process and insures maximum surface detail while providing a second color for surface highlights and distinctive grout line look. Stampcrete’s special acrylic base sealer added in the curing process provides full color depth and richness with maximum concrete protection.
GUIDELINES Highly trained ACI Stampcrete contractors perform all work. All work shall meet ASTM C 94 and ACI 332 requirements for placement of concrete surfaces. This includes sub-grade preparation and forming concrete. When the concrete truck arrives, add specified Stampcrete color together with Stampcrete reinforcing fibers. Mix integral color and fi bers thoroughly in concrete truck prior to placement. The concrete is then placed at a thickness of 4" (10 cm) or 6" (15 cm) for heavier uses, screed, bull floated, and edged before applying clear or colored release agent on the surface. Release agent is applied evenly over the entire surface before stamping the surface. While in the plastic state, place stamping tools onto the surface and start stamping by using tamper to get the desired texture. Remove excess release agent and saw cut all control cuts 1/3 the thickness of slab, within 12 hours. When surface is dry, apply two coats of Stampcrete clear acrylic sealer to protect surface from fading or staining due to nature’s elements.
CONCRETE MIX DESIGN In freeze-thaw areas, the concrete mix design shall be a minimum of 3,500 psi (24.5mpa), compressive strength shall be 3,500 psi (24.5mpa) at 28 days +. Portland Cement shall meet the requirements of ASTM-C 150. Cement content shall be 564 lbs./yd. (335 kg/m3), 1 bag fiber/yd (1 fiber bag/m3). Add Color as specified. Slump 4 inch + 1 inch (80/100mm), maxi mum water-cement ratio shall be .44 by weight. Coarse aggregate shall be in accordance with ASTM C 33 size 3/4" minus aggregate (14mm). Air-Entrainment 7% (+/- 1%) while using Integral Color, or 3% (+/- 1%) using Color Hardeners. In non-freeze areas the concrete mix design shall be a minimum 3,000 psi (24.5mpa), compressive strength shall be 3,000 psi (24.5mpa) at 28 days +. Portland Cement shall meet the requirements of ASTM-C 150. Cement content shall be 517 lbs./yd. (280 kg/m3), 1 bag fiber/yd. (1 bag fiber/m3). Add Color as specified. Slump 4 inch + 1 inch (80/100mm), maximum water-cement ratio shall be .44 by weight. Coarse aggregate shall be in accordance with ASTM C 33 size 3/4" minus ag gregate (14mm), Air-Entrainment 7% (+/- 1%) while using Integral Color, or 3% (+/- 1%) using Color Hardeners.
AMERICAN LAWN CARE - 167 WASHINGTON ST
- PEMBROKE, MA 02359
PHONE 781-826-1118 FAX 781-826-1118 EMAIL
SERVICE1@AMERICANLAWNCARE.COM
